Dumped/flashed MMX on SNES v3 boards.
created discrete_exp0_mapper_wr to try and write to mapper but not flash
for discrete boards but doesn't seem to work for some reason so commented
out for now.
tested and verified on purple, green, and yellow/orange avr kazzos and
stm32 inlretro6 proto, and stm32 adapter with yellow kazzo board
AVR takes ~17.5sec to dump 256KB -> 1:10 for 1MByte = 14.6KBps
STM takes ~8.5sec to dump 1MByte = 120KBps
STM32 usb driver is far from optimal as it's setup to be minimal with only
8byte endpoint0 to make an effort to align avr and stm. Larger endpoints
and bulk transfers should greatly speed up stm usb transfers
refactored firmware buffer.c and implemented most of the required opcodes
added check that should cover if device isn't ready for a IN/OUT
transfer. Does this by usbFunctionSetup returning zero which causes the
device to ignore the host. Don't think I've got the stm32 usb driver
setup properly to handle this not sure I fully understand Vusb driver
either. Anyway, hopefully it works well enough for now and keep this in
mind if issues crop up in future.
Still haven't implemented usbFunctionWrite, not sure stm usb driver is
setup properly yet either..
build sizes:
avr yellow/orange: avr-size build_avr/avr_kazzo.elf
text data bss dec hex filename
5602 6 674 6282 188a build_avr/avr_kazzo.elf
previous builds of avr code size was ~6.4KB when flashing and dumping was working.
AVR bootloader is 1.7KB taking up majority of 2KB boot sector.
So AVR has 16KB - 2KB boot = 14KB available, using ~44% of non-boot sector
available flash Have 4 buffers defined, and 512B of raw buffer defined so using
~65% SRAM Making pretty good use of the chip just for basic framework.
Not a ton of room for board/mapper specific routines, so will have to keep this
in mind. Creating more generic routines to save flash will come with a speed
hit, but perhaps we shouldn't worry too much about that as devices below
really boost speed without even trying. There is some sizable amount of
SRAM available could perhaps load temporary routines into SRAM and execute
Also have ability to decrease buffer sizes/allocation. Perhaps routines
could actually be store *IN* the raw buffers.. ;)
stm adapter: arm-none-eabi-size -t build_stm/inlretro_stm.elf
text data bss dec hex filename
7324 0 680 8004 1f44 build_stm/inlretro_stm.elf
Currently targetting STM32F070C6 which has 32KB flash, 6KB SRAM
Could upgrade to STM32F070CB in same LQFP-48 package w/ 128KB/16KB
Don't think that'll be of much value though especially with limitation
on connectors for adapter.
So currently don't have user bootloader, only built in ones.
8KB of 32KB avaiable flash = 25% utilization
680B of 6KB available sram = 11% utilization
32KB device doubles amount of available flash compared to AVR, although
stm32 code isn't quite a condensed compared to AVR.
stm inlretro6: arm-none-eabi-size -t build_stm/inlretro_stm.elf
text data bss dec hex filename
6932 0 680 7612 1dbc build_stm/inlretro_stm.elf
Mostly limited to STM32F070RB as choosing device requiring XTAL, and
desire large number of i/o. This device provides 128KB flash, 16KB SRAM
Currently using 7.6KB/128KB flash = 6% utilization
Currently using 680B/16KB SRAM = 4.1% utilization
LOTS of room for growth in this device!! Part of why I choose it over
crystalless 072 version, as it came with more flash for less cost.
Also hardly making use of 1KB of USB dedicated SRAM:
32B buffer table entries
16B endpoint0 IN/OUT
48B of 1024B available = 4.6% utilization
Detecting mirroring code working and tested
Started working on buffer operations from host
Current code compiles but not yet at point where can start testing
Adding cpu page read to nes.c to have faster dumping operations.
moving enums to shared as gets used quite a bit communicating between device and host.
cleaned up firmware pinport.h used PURPLE/GREEN KAZZO for all #ifdef's
AVR Memory Usage
----------------
Device: atmega164a
Program: 3404 bytes (20.8% Full)
(.text + .data + .bootloader)
Data: 53 bytes (5.2% Full)
(.data + .bss + .noinit)
final kazzo design hex commited as comparable build to the past two commits of green/purple.
So this .hex commit is apples to apples with recently commited purple/green .hex commits.
Able to read PRG-ROM flash chip's manf and device ID from commandline.
New dictionaries io and nes along with firmware files to support.
now have io_reset, nes_init, and snes_init io.c functions
nes.c functions including discrete_exp0_prgrom_wr and emulate_nes_cpu_rd.
New dictionary.c/.h for host to make dictionary calls easier including
setting proper return data lengths based on opcode.
adding nop command to pinport.h
AVR Memory Usage
----------------
Device: atmega164a
Program: 2960 bytes (18.1% Full)
(.text + .data + .bootloader)
Data: 53 bytes (5.2% Full)
(.data + .bss + .noinit)
Paul Black ASUS win7