I made a commit earlier this week but messed things up by not pulling
from the master and things weren't updated... Here's the notes from
that commit:
Author: Paul XPS <paul@infiniteneslives.com>
Date: Tue Nov 6 22:45:52 2018 -0600
Large commit biggest feature add is NES MMC3 support including Save RAM
(aka WRAM/PRGRAM) support including dumping and writing save files.
The MMC3 script & method of dumping/flashing is the most forward
thinking script/firmware so far. Finally starting to form a clear
vision of how I want to handle flashing/dumping variations with mappers.
Biggest thing is having the host handle the mapper init & banking
control. In the view of the firmware, it's only responsible for knowing
how to flash a bank. And dumping is even more generic with the host
just telling what address range to read. Things will get more complex
with support of mappers with bus conflicts. But ready to start
converting these old hacked methods to be more like the MMC3 means.
Have some early support for dumping gameboy using the snes script as the
pinouts are nearly identical. Along with testing of toggling between 3v
GBA and 5v DMG.
Have some early support for INLretro NES only version which uses a
smaller mcu because it doesn't need to support large 16bit carts. Still
have to get this completed.
Added support for CNROM, but I'm not sure if it's actually working. Going
to restart with NROM and start updating the currently supported
mappers to be more like MMC3.
But this also includes some new updates from the second half of the week:
Started updating existing NES scripts to use new MMC3 methodology. Got
NROM, CNROM, BNROM, & Color Dreams working. On the host side only
needed to add nes.c functions for specific flash algos. Able to delete
significant amounts of mapper specific code from flash.c
Got some basic SNES script support with new methodology for Catskull
elect 5v PLCC SNES LoROM board. And INL SNES HI/LO-ROM 3v board as
well. These don't yet use buffer writes, just single byte writes.
Also having issues with Mirroring test/sensing again. Driving me crazy,
but don't really care about it at the moment and not sure what's wrong..
So just committing that broken for now. Looking to remove this
functionality from the firmware side as the host should be controlling
most of this.
Looking to add SNES RAM & buffered writes. Also need to test some of
the HIROM code as I just added it in there while I did the LOROM stuff..
prototype which has STM8 CIC driving flash /OE with inversion of SYS /RST.
STM8 CIC is running at 16Mhz, and doesn't actually function as CIC. Still
need to come up with special way to signal to CIC that it's plugged into a
programmer and not a console.
Things aren't as fast as they could be, but they're good for now and
proved working on all kazzo versions. Expecting decent speedup could be
aquired by optimizing the flash routine, not changing address unless
needed, or only changing low byte of address, etc. Could also let the
host put the flash chip in unlock bypass mode and keep it there until done
with flashing.
Current speeds:
INL6: 42.2 KBps flashing, 92KBps dumping
stm adapter: 25.3 KBps flashing, 96KBps dumping
AVR kazzo: 18.0KBps flashing, 14.3KBps dumping
Was able to get the inl6 up to 59KBps flashing. Which was 35sec total
flash time for 16mbit chip which has typical flash time of 22s plus
overhead. This got slowed down when supporting stm adapter as checks for
buffer status were required from what I recall. Also fixing flash polling
routine AVR found slowed things down.
Was able to get 140KBps dump time on inl6 with 16mbit SNES flash. This
was slowed when supporting stm adapter which brought out issue with stm32
usb driver. Locks up the device if the buffer isn't fully dumped prior to
calling. Need to get driver to support sending NAKs until data is dumped.
Current fix for checking buffer status slows things down for all devices.
AVR brought out issue with SNES v3 design where we can't rely on flash
poll data to toggle between reads as /OE and /CE are stuck low. Have to
toggle /RESET slowly to toggle /OE and ensure we don't move on to next
byte until previous is fully flashed.
STM32 found initial issue where /WR should be set low first to set
direction of data level shifter, then set /ROMSEL low to enable level
shifter output. Not doing this caused bus conflicts between the two
causing flakey writes where not all bits were getting cleared.
lua scripts currently force SNES, need to add smart check that identifies
SNES flash board if vector data is 0xFFFF. Also funky order where it
always erases after flashing as this was more convient for testing.
While this commit is far from ideal, it's stable and I've done my best to
not commit junk that will cause problems later. Just make sure to always
verify dumping algo before assuming something is wrong with writes!
works on both inl6 and original kazzo just fine. Dumping v3 prototype has
a few byte corruptions on inl6, but is fine on original kazzo. The same
bytes often fail, but not consistently. Tinkered with adding delay, but
that didn't help. Also have issue with adapter not dumping properly.
Prob bug with HIGH ADDR on that board need to sort out still. Going to
focus on erasing and dumping next then come back to some of these issues.
enumeration with host, no vendor/class requests handled.
move avr builds into avr_release dir
move original source files into source/old for future reference.
avr-size avr_kazzo.elf
text data bss dec hex filename
1496 2 43 1541 605 avr_kazzo.elf
cleaned up firmware pinport.h used PURPLE/GREEN KAZZO for all #ifdef's
AVR Memory Usage
----------------
Device: atmega164a
Program: 3404 bytes (20.8% Full)
(.text + .data + .bootloader)
Data: 53 bytes (5.2% Full)
(.data + .bss + .noinit)
final kazzo design hex commited as comparable build to the past two commits of green/purple.
So this .hex commit is apples to apples with recently commited purple/green .hex commits.
Paul XPS